AT93C46 datasheet, AT93C46 circuit, AT93C46 data sheet: ATMEL – 3-Wire Serial EEPROMs,alldatasheet, datasheet, Datasheet search site for Electronic. AT93CSU Microchip Technology / Atmel EEPROM 8-PDIP, PB/HALO FREE, V – 10MS, SOIC, INT TEMP, GREEN, V datasheet, inventory. AT93C46 datasheet, AT93C46 pdf, AT93C46 data sheet, datasheet, data sheet, pdf, Atmel, 1/2/4K, 3-wire Bus Serial EEPROM.

Author: Moogugul Tugal
Country: Georgia
Language: English (Spanish)
Genre: Love
Published (Last): 22 June 2016
Pages: 20
PDF File Size: 20.72 Mb
ePub File Size: 1.41 Mb
ISBN: 996-2-30972-578-5
Downloads: 76154
Price: Free* [*Free Regsitration Required]
Uploader: Meztiktilar

(PDF) AT93C46 Datasheet download

Thanks for your help!!! I have complated the firmware for that. But I am not clear how to evaluate the design. I had 93c46 ‘s datasheet and wrote a firmware. Can I find such a library file P.

What a library can work with Atmel AT93C46?

Can you read back the same data as it was written to it? Because pic should not generate the clock while reading.

Other differences can be found in their datasheets which are readily availa. I use c51 programmed a datashete interface program visit cs,the program can visit 93c46 and xicro ,but cs don’t response, who can help me?

SPI with and 93C The 93c46 has 3-wire serial interface Din, Dout and Clock whereas the 24C04 uses 2-pin I2C interface and can be easily connected to any host I2C device or bus.

  BUDO SAITO PDF

AT93C46 Datasheet PDF

But it didn’t work. Thank you Please see the text below. And i am planning to do that with Proteus.

Chips should read the data from pic. Attached is a revised version of your original file eewr. Proteus-Microwire-req – have you seen it? Seems your totally not familiar with datasheet reading o; 2MHz is the maximum clock frequency for the 93c46 clock line mostly for 5V operation only.

I want to remove 93c46 with pic code. SPI with 89v51rd2 and 93C Indicate the suffix letter whether 93C86A or 93C86B follow the datasheet if it is B version as regards s.

Here you have some hints: I post full my code used 93c46 here could you fix it for me, please!?! Now I want to explain that I did. This was revised looking at information in the AT 93c46 data sheet. I extracted it from winpic Only will send shifted data according to clock and address. Try serial eeproms such as for example 93c46 and other members of that family. The file is un-tested as a program.

  M3N78 PRO MANUAL PDF

But instead of trying this circuit on board, first i want to simuate in PC. However, there is no library about 93c46 in Proteus. Hi, i have an JDP programmer. Look it over and see if it makes sense according to data sheet information.

Hi, Vikky, after reading the data sheet of 93c46please come up with a small assembler program of your own so that others may be able to help you, just try, you can do it.

Buy Products Online from China Wholesalers at

Where is my fault? If you can use eeproms with I2C or 3-wire interfaces then goto: PIC93c46and others. Just give me an idea about the protocol used. But I wrote code for it but not work at93x46. Do you use exact timing as described in the datasheet for writing to it?

PC Programming and Interfacing:: The software currently supports these devices: Some chips are on board. Thanhs agains so much!!!